This feature is part of the ipbasek9 technology package. The license is displayed as the throughput license. You can upgrade the throughput of the ESP from 2. If you want to determine the current throughput level of the ESP, run the show platform hardware throughput level command.
The following example shows the output of this command before the performance upgrade license is applied:. In the user EXEC configuration mode, enter the enable command. Enter configure terminal command to enter the global configuration mode. To save the configuration, enter the copy running-config startup-config command. To reload the router enter reload.
A reload is required to activate the throughput level. Cisco Boost performance license allows you to increase the throughput bandwidth.
You can enable Boost performance license in the follwoing modes:. Configure the device with the license install bootflash:xxx command as shown in this example. The platform hardware throughput level boost is automatically added to the configuration. Save the configuration and reload the device to enable Boost performance license. After the reload, the Boost Performance is activated as shown in this example. This section describes the processes to activate and deactivate the Boost performance license from the device with two use-cases.
Boot the device in Smart License mode. The boost performance command is not visible without registering in the Smart Portal. After successfully registering to the Smart Portal, check the availability of the boost performance licenses in the smart account. Use the platform hardware throughput level boost command to enable the feature. You need to save the configuration. If a valid license is still available in the smart account, the Boost Performance feature is enabled after the device is reloaded.
To check for the platform hardware throughput level, use the show platform hardware throughput level boost command. If there are not enough licenses, it shows an Out of Compliance OOC message, and the throughput level change does not take effect even after the device is reloaded.
The device is in the smart license mode with boost performance command configured. Use show running-config and the show license summary commands to display the boost performance information from the smart account. Use the no platform hardware throughput level boost command to disable the functionality.
The command is removed from the configuration, but the license is released only after the device is reloaded. One count of boost performance license is reduced from the usage pool, and one license is returned to its original pool.
The boost performance behavior is determined by the availability of the license in its Smart Account with Boost Performance activated in CSL:. To configure the throughput level, perform the following steps and to upgrade the throughput level use the. Configure the device with the platform hardware throughput level boost command and then use show running-config to check if the boost performance license is activated.
Use show license to verify if boost performance is in use and in a permanent license mode. Enable smart license by license smart enable command. After registration in success, the license request is sent to the smart portal for validation. Boost performance is valid if successful, no reload is required. Otherwise the platform hardware throughput level boost is unattached from configuration. Boost performance functionality is disabled after reload. During the transition but before the registration, we have to maintain the Evaluation mode for the license if the is existing to avoid an extra reload later.
This section includes these two use-cases that describe what happens during the transition from Smart License to Cisco Software License. Device show license to ensure that Smart License and Boost performance licenses are enabled.
Check the Smart License Account if the boost performance license is consumed from the corresponding device. Check the availability of the boost performance license, you may decide to retain the boost command. Use no platform hardware throughput level boost in the show running-configuration.
Device show license to check if smart license is enabled, but boost performance license is not in the list. Check the Smart License Account, the boost performance license is not used from the corresponding device. To remove Smart License, use no license smart enable. Check the availability of the boost permanent license to add the boost keyword.
If there is no permanent license available, then no boost performance command and functionality is likely to change. To install or upgrade the software, use one of the following methods to use the software from a consolidated package or an individual package.
Also see the overview section. To upgrade a consolidated package, copy the consolidated package to the bootflash: directory on the router using the copy command. After making this copy of the consolidated package, configure the router to boot using the consolidated package file. The following example shows the consolidated package file being copied to the bootflash: file system via TFTP.
The config register is then set to boot using boot system commands, and the boot system commands instruct the router to boot using the consolidated package stored in the bootflash: file system. The new configuration is then saved using the copy running-config startup-config command, and the system is then reloaded to complete the process. To choose between running individual packages or a consolidated package, see Installing the Software - Overview section.
Installing Subpackages from a Consolidated Package. Installing a Firmware Subpackage. Perform the following procedure to obtain the consolidated package from a TFTP server. Another variation of this procedure obtains the consolidated package from a USB flash drive. Copy the consolidated package to the TFTP server. Shows the version of software running on the router. This can later be compared with the version of software to be installed. Displays the previous version of software and that a package is present.
Creates a directory to save the expanded software image. You can use the same name as the image to name the directory. Boots the consolidated package, by specifying the path and name of the provisioning file: packages. Displays the version of the newly installed software. The initial part of the example shows the consolidated package, isruniversalk9. This is a prerequisite step. The remaining part of the example shows the consolidated file, packages.
The steps for installing subpackages from a consolidated package on a USB flash drive are similar to those described in Installing Subpackages from a Consolidated Pacakage section. Also see Overview section. During the upgrade, do not power cycle the device. The following example illustrates the boot process of a consolidated package:. Obtain a consolidated package that contains your required firmware package and expand the package. Make a note of the location and name of the firmware package and use this information in the steps below for URL-to-package-name.
You can install a firmware subpackage if the router has been configured using, for example, Managing and Configuring a Router to Run Using Individual Packages. Firmware subpackages are not released individually. You can select a firmware package from within a consolidated package after expanding the consolidated package.
The firmware package can then be installed as shown in the procedure below. Read the Release Notes document pertaining to the consolidated package to verify that the firmware within the consolidated package is compatible with the version of Cisco IOS XE software that is currently installed on a router.
Boots the consolidated package by specifying the path and name of the provisioning file: packages. The initial part of the following example shows the consolidated package, isruniversalk9.
When you boot the router in packages. You need to follow the steps described in Installing a Firmware Subpackage section before proceeding with the firmware upgrade. If you do not boot the router in packages. Reload the hardware module subslot to boot the module with the new firmware. Expands the platform software package to super package. Boots the super package by specifying the path and name of the provisioning file: packages.
Copies the NIM firmware subpackage into bootflash:mydir. Reloads the hardware module subslot and boots the module with the new firmware. Displays the version of the newly installed firmware. The following example shows how to perform firmware upgrade in a router module:.
Skip to content Skip to search Skip to footer. Book Contents Book Contents. Find Matches in This Book. PDF - Complete Book 5. Updated: March 2, Chapter: Installing the Software. These are the two main methods to install the software: Managing and Configuring a Router to Run Using a Consolidated Package —This method allows for individual upgrade of subpackages and generally has reduced boot times compared to the method below.
Rommon Compatibility Matrix The following table provides information about Cisco Series Integrated Services Routers supported in each rommon release.
Table 1. Note The rommon release Table 2. Table 3. Note An exception to this is that if a new or upgraded module firmware package is subsequently installed, it need not be in the same directory as the provisioning file. File Systems The following table provides a list of file systems that can be seen on the Cisco series routers.
Table 4. Autogenerated File Directories and Files This section discusses the autogenerated files and directories that can be created, and how the files in these directories can be managed. Table 5. Autogenerated Files File or Directory Description crashinfo files Crashinfo files may appear in the bootflash: file system.
Important Notes About Autogenerated Directories Important information about autogenerated directories include: Autogenerated files on the bootflash: directory should not be deleted, renamed, moved, or altered in any way unless directed by Cisco customer support. Note Altering autogenerating files on the bootflash: may have unpredictable consequences for system performance.
Flash Storage Subpackages are installed to local media storage, such as flash. Note Flash storage is required for successful operation of a router. Configuring the Configuration Register for Autoboot The configuration register can be used to change router behavior. Set the configuration register to 0x0 to boot into ROM, by using one of the following commands: In Cisco IOS configuration mode, use the config-reg 0x0 command.
Note The console baud rate is set to after changing the confreg to 0x or 0x0. Consolidated Packages One of the following two consolidated packages images is preinstalled on the router: universalk9 —Contains the ipbasek9 base package and the securityk9 , uck9 , and appxk9 technology packages.
Note The term npe stands for No Payload Encryption. Note The terms super package and image also refer to a consolidated package. The following examples show how to obtain software authenticity information and internal details of a package: Displaying Digitally Signed Cisco Software Signature Information section Obtaining the Description of a Module or Consolidated Package section Many features within the consolidated package are contained in the ipbasek9 base package.
Technology Packages Technology packages contain software features within a consolidated package. The following is a list of technology packages: Note In Cisco Series Integrated Series Routers, although L2TPv2 sessions comes up without appxk9, you need the appxk9 license for the traffic to go through the sessions. Performance The performance feature, which allows for increased throughput, is enabled by the performance license.
To exit global configuration mode, enter exit. You have to deregister and register back the device from the CSSM to execute the boost license command. Device show running-config include throughput platform hardware throughput level boost Save the configuration and reload the device to enable Boost performance license. Boost Performance License in Smart License Mode This section describes the processes to activate and deactivate the Boost performance license from the device with two use-cases.
Enable the boost performance license : Boot the device in Smart License mode. Return of license : The device is in the smart license mode with boost performance command configured. Note The command is removed from the configuration, but the license is released only after the device is reloaded.
The throughput level does not take effect until the device is reloaded. The license visibility is available till the device is reloaded. The boost performance behavior is determined by the availability of the license in its Smart Account with Boost Performance activated in CSL: To configure the throughput level, perform the following steps and to upgrade the throughput level use the Configure the device with the platform hardware throughput level boost command and then use show running-config to check if the boost performance license is activated.
When boost performance is in use: Device platform hardware throughput level boost Device show license to ensure that Smart License and Boost performance licenses are enabled. Remove Smart License Device no license smart enable Check the availability of the boost performance license, you may decide to retain the boost command. No extra reload is required.
When boost performance is not in use : Use no platform hardware throughput level boost in the show running-configuration. To remove Smart License, use no license smart enable Check the availability of the boost permanent license to add the boost keyword. VIP Mentor. Improve the world by lending money to the working poor or share a meal with a hungry child. Leo Laohoo.
VIP Community Legend. If you really want this specific old version then contact TAC. Post Reply. Latest Contents. Created by Emmanuel Tychon on AM. Cisco cellular software contains a database of well-known APNs based on the country and Created by Leo Laohoo on PM.
The IT Blog Awards is now accepting submissions! Created by caiharve on PM. Submit your blog, vlog or podcast today. They make geeky cool. They are both educator Ask a Question.
Find more resources. Blogs Networking Blogs Networking News. Project Gallery. New Community Member Guide. Related support document topics.
0コメント